Aurora Sound Studio HD Bedienungsanleitung

User Manual Please Note: The LT-HD requires your Aurora converter to have Firmware Version 14 or later. Any Aurora shipped from L

Page 7 8. Secure LT-HD with three screws; one on the standoff and two from the back panel of Aurora. Keep screws loose until LT-HD is properly aligne

Page 8 7 External Connections The physical connection between the Aurora/LT-HD and Digidesign Core, Process or Accel cards is very straightforward.

Page 9 channels of analog + 8 channels of digital or 16 channels of analog I/O at one time. It is not possible however, to access 16-channels of digit

Page 10 8.1 Loop Sync ProTools|HD features a synchronization system called Loop Sync, which potentially simplifies establishing clock relationships b

Page 11 9 ProTools Setup When an Aurora/LT-HD is connected to a Digidesign Core or Accel/Process card it will automatically be integrated as an I/O c

Page 12 Aurora 8 Aurora 16: 16-channel mode Aurora 16: 32-channel mode Notes: 16 active channels at a time: 8 analog inputs, 8 analog outputs, 8 d

Page 13 Aurora 8 Aurora 16: 16-channel mode Aurora 16: 32-channel mode 192 I/O #1 (channels 1-8) 192 I/O #2 (channels 9-16) Sample Rates e Al

Page 14 Aurora 8 Aurora 16: 16-channel mode Aurora 16: 32-channel mode 192 I/O #1 (channels 1-8) 192 I/O #2 (channels 9-16) S/PDIF Format i N

Page 15 Aurora 8 Aurora 16: 16-channel mode Aurora 16: 32-channel mode 192 I/O #1 (channels 1-8) 192 I/O #2 (channels 9-16) Analog In: Ref. L

Page 16 Aurora 8 Aurora 16 : 16-channel mode Aurora 16: 32-channel mode 192 I/O #1 (channels 1-8) 192 I/O #2 (channels 9-16)Input Forma

Page 17 9.2 I/O Setup Page This page within the ProTools software is where active input and output devices that are defined in the hardware setup pa

Page 18 10 Aurora Parameter Controls Since the Aurora with an LT-HD installed is intended to be accessed and identified as a Digidesign 192 I/O, a

Page 19 AES B This is not a possible setting when using an Aurora 16 with ProTools. If the Aurora is to slave to an AES signal, the clock source shou

Page 20 10.2 Aurora Remote Control Software The Aurora Remote Control software can operate on an OSX or Windows PC computer via a Lynx AES16 audio i

Page 21 Item Description Status y Digital Input and Output Meters Functional u Digital Output Monitor Source A and B monitor source selection Lo

Page 22 11 Updating the firmware on the LT-HD Updating the firmware on the LT-HD uses the same process as updating the firmware on the Aurora. With

Page 23 12 Specifications DIGILINK PORTS Number / Type One Primary, One Expansion Channels Aurora 8: 16 channels at all supported sample rates Auror

Page 24 13 Support We are devoted to making your experience with the LT-HD trouble-free and productive. If the troubleshooting and operational secti

Page 25 14 Warranty Information One year Free Labor / One year Parts Exchange This product must be returned to the factory for repair. Who Is Cove

User Manual Table of Contents 1 Introduction...

Page 1 1 Introduction Thank you for purchasing the LT-HD™! We are proud to provide you with a reliable, professional-quality product for your digita

Page 2 3 Before You Begin We recommend that you read through the manual to acquire an overview of the installation procedure and use of the LT-HD. Th

Page 3 4 Nomenclature used in this manual The following typographic conventions are used in this manual:  ALL UPPER CASE TEXT refers to a specific

Page 4 6 Installation Procedure 1. Remove the AC power cord and take the top off of the Aurora 16 or Aurora 8. There are seven large screws plus one

Page 5 3. Remove the LSlot Expansion Port cover above the AES I/O Ports by removing the two mounting screws. Set these two screws aside, as they will

Page 6 5. Install the standoff post (included with the LT-HD) in this same hole. 6. Grounding yourself to the earth ground, remove the LT-HD from